AF’s Weblog

December 10, 2010

Making Equalization Work For You

Filed under: Equalizers — Tags: , — audiofanzine @ 11:31 am

Equalization is one of the most important and powerful tools in the recording enthusiast’s arsenal, yet too many people adjust equalization with their eyes – not their ears. For example, one time after doing a mix, I noticed the client writing down all the EQ settings I had made. When I asked why, he said it was because he liked the EQ and wanted to use the same settings on these instruments in future mixes.

Wrong! EQ is a part of the mixing process; just as levels, panning, and reverb are different for each mix, EQ should be custom-tailored for each mix as well. But to do that, you need to understand how to find the magic EQ frequencies for particular types of musical material, as well as what tool to use for what application.

There are three main applications for EQ:

  1. Problem-solving
  2. Emphasizing or de-emphasizing an instrument in a mix
  3. Altering a sound’s personality

Each application requires specialized techniques and approaches.

Problem Solving

EQ can fix a variety of problems, and the tool of choice is usually a parametric equalizer, which consists of a limited number (typically 1-8) of frequency bands (Fig. 1). For each band, you can change not just the degree of boost or cut, but also the frequency at which this boosting or cutting occurs, as well as how wide a range of frequencies is affected – from very sharp to very broad. (“Pseudo-parametric” equalizers omit the bandwidth control, and the lack of this can seriously hamper the experienced EQ aficionado. Arguably, manufacturers err on the side of too narrow a fixed bandwidth, which makes it difficult to do subtle changes.)

Fig. 1: The PSP Audioware MasterQ is a high-quality equalizer plug-in for digital audio workstations with seven frequency-altering stages. Going from left to right, these are a highpass filter, low frequency shelving EQ, three parametric stages, high frequency shelving EQ, and a lowpass filter.

As one example of how you’d use a parametric EQ, slicing a sharp notch at 60Hz (50Hz in Europe) can knock hum out of a signal; trimming the high frequencies can remove hiss. Another common problem is an instrument with a resonance or peak that interferes with other instruments, or causes level-setting difficulties. Following is a procedure that takes care of this situation.

Several years ago I produced an album by classical guitarist Linda Cohen (Angel Alley, which was re-released on CD). She had a beautiful instrument with a full, rich sound that projected very well on stage, thanks to a strong body resonance in the lower midrange that caused a major level peak. However, recording was a different matter from playing live. If levels were set so the peaky, low frequency notes didn’t overload the recording media, the higher guitar notes sounded weak by comparison.

Although compression/limiting was always an option, it altered the guitar’s attack; while this effect might have gotten lost in an ensemble, it stuck out with a solo instrument. A more natural-sounding answer was to use EQ to apply a frequency cut equal and opposite to the natural boost, thus leveling out the response. But there’s a trick to finding problem frequencies so you can alter them; the following works like a charm.

  1. Turn down the monitor volume – the sound might get nasty and distorted during the following steps.
  2. Set the EQ for lots of boost (10-12dB) and fairly narrow bandwidth (around a quarter-octave or so).
  3. As the instrument plays, slowly sweep the frequency control. Any peaks will jump out due to the boosting and narrow bandwidth. Some peaks may even distort.
  4. Find the loudest peak and cut the amplitude until the peak falls into balance with the rest of the instrument sound. You may need to widen the bandwidth a bit if the peak is broad, or use narrow bandwidth for single-frequency problems such as hum.

This technique of boost/find the peak/cut can help remove midrange “honking,” strident resonances in wind instruments, and much more. Of course, sometimes you want to preserve these resonances so the instrument stands out, but many times applying EQ to reduce peaks allows instruments to sit more gracefully in the track.

Digital workstation EQ, as found in hard disk recording systems, can be particularly effective due to its precision. In one of my more unusual projects, I needed to remove boat motor noise from some whale samples. Motor noise is not broadband, but exists at multiple frequencies. Applying several extremely sharp and narrow notches at different frequencies took out each component of the noise, one layer at a time, until the motor noise was completely gone.

This type of problem-solving also underscores a key principle of EQ: it’s often better to cut than boost. Boosting uses up headroom; cutting opens up headroom. In the example of solving the classical guitar resonance problem, cutting the peak allowed for bringing up the overall gain to record a much higher overall level.

Let’s take a closer look…

Other EQ Tips

Problem-solving and character-altering EQ should be applied early on in the mixing process, as they will influence how the mix develops. But wait to apply most EQ until the process of setting levels begins; remember, EQ is all about changing levels – albeit in specific frequency ranges. Any EQ changes you make will alter the overall instrumental balance.

Another reason for waiting a bit is that instruments EQ’ed in isolation to sound great may not sound all that wonderful when combined. If every track is equalized to leap out at you, there’s no room left for a track to “breathe.” Also, you will probably want to alter EQ on some instruments so that they take on more supportive roles. For example, during vocals consider cutting the midrange a bit on supporting instruments (e.g., rhythm guitar) to open up more space in the audio spectrum for vocals.

Finally, remember that EQ often works best when applied subtly. Even one or two dB of change can make a significant difference. However, inexperienced engineers often do something such as increase the bass too much, which makes the sound too muddy, so they increase the treble, and now the midrange sounds weak, so that gets turned up…you get the idea. One of your best “reality checks” is an equalizer’s bypass switch. Use it often to make sure you haven’t lost control of the original sound!

To read the full detailed article:  Making Equalization Work For You

Advertisements

Leave a Comment »

No comments yet.

RSS feed for comments on this post. TrackBack URI

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Blog at WordPress.com.

%d bloggers like this: